Electrónica Cambiar MMSI en radios UNIDEN/JMC

[Juanitu]

Originalmente publicado por golden dreams

Juanitu y la tuya, pudo el electrónico tunerla o tenemos que cambiar de radio para la holandesa?

Efectivamente, me confirma mi electrónico que sí que puede con ello. Parece que a través de un socio suyo que tiene el famoso HARDWARE (cablecito y caja misteriosa). Si todo sale bien será alrededor de 60 euros el cambio. Eso no incluye desinstalación del barco e instalación, pero hasta ahí sí que llegamos...

Si alguien está en la zona le digo la tienda de electrónica naval que es y que se ponga de acuerdo con ellos. A mi me hacen "todo" lo de electrónica desde que les conocí.

[maka]

. si el barco es bandera española, al darlo de baja en España te dan de baja
del mmsi, por lo que hay que borrarlo e introducir otro mmsi
. pero si el barco está comprado por ejemplo en Francia al darte de baja no
te dan de baja del mmsi, éste permanece
. pero antes de realizar estos cambios hay que ver que el aparato sea homologado
en la CE, sino en Bélgica no lo aceptarán
..................................

en la vhf icom IC-M 421
en google se baja el manual
en la pagina 6 lo explica

6
MMSI code programming
The 9-digit MMSI (Maritime Mobile Service Identity: DSC self
ID) code can be programmed at power ON.
This code programming can be performed only once.
After the code programming, it can be changed only
by your dealer or distributor.
q Turn power OFF.
w While pushing [MENU], turn power ON to enter MMSI
code programming condition.
e After the display appears, release [MENU].
r Push [MENU] again to enter the DSC menu.
t Push [] or [] to select “Set up,” push [ENT].
y Push [] or [] to select “MMSI Check,” push [ENT].
u Push [] or [] to set the specific 9-digit MMSI code.
• Push [CH•DUAL] or [16•C] to move the cursor forward or backward,
respectively.
• Push [SCAN•TAG] to clear the MMSI code.
• Push [CLR] to cancel and exit the condition to the set up menu.
i After input the 9-digit code, push [ENT] to set the code.
• Returns to the set up menu.
o Push [CLR] or [] to select “Exit,” push [ENT].
• Returns to the DSC menu.
• Repeat again to return to the normal operation condition.
Information for FRG version
The DSC channel group MUST be selected before entering
the DSC menu. (p. 7) If other channel group is selected, DSC
operation cannot be performed.
• You should select the DSC channel group before turning power
OFF for entering the MMSI code programming condition.
--DSC Menu--
MMSI Check
Input 9 digits
_________
<CLR˘Exit / ENT˘OK>--DSC Menu--Set upDEL:INDV ID ≤DEL:Group IDOffset Time˘MMSI Check ≥--DSC Menu--Select ItemPosition Input
Received Calls

[Kane]

Si, pero...

Originalmente publicado por maka

. si el barco es bandera española, al darlo de baja en España te dan de baja
del mmsi, por lo que hay que borrarlo e introducir otro mmsi
. pero si el barco está comprado por ejemplo en Francia al darte de baja no
te dan de baja del mmsi, éste permanece
. pero antes de realizar estos cambios hay que ver que el aparato sea homologado
en la CE, sino en Bélgica no lo aceptarán
..................................

en la vhf icom IC-M 421
en google se baja el manual
en la pagina 6 lo explica

6
MMSI code programming
The 9-digit MMSI (Maritime Mobile Service Identity: DSC self
ID) code can be programmed at power ON.
This code programming can be performed only once.
After the code programming, it can be changed only
by your dealer or distributor.
q Turn power OFF.
w While pushing [MENU], turn power ON to enter MMSI
code programming condition.
e After the display appears, release [MENU].
r Push [MENU] again to enter the DSC menu.
t Push [] or [] to select “Set up,” push [ENT].
y Push [] or [] to select “MMSI Check,” push [ENT].
u Push [] or [] to set the specific 9-digit MMSI code.
• Push [CH•DUAL] or [16•C] to move the cursor forward or backward,
respectively.
• Push [SCAN•TAG] to clear the MMSI code.
• Push [CLR] to cancel and exit the condition to the set up menu.
i After input the 9-digit code, push [ENT] to set the code.
• Returns to the set up menu.
o Push [CLR] or [] to select “Exit,” push [ENT].
• Returns to the DSC menu.
• Repeat again to return to the normal operation condition.
Information for FRG version
The DSC channel group MUST be selected before entering
the DSC menu. (p. 7) If other channel group is selected, DSC
operation cannot be performed.
• You should select the DSC channel group before turning power
OFF for entering the MMSI code programming condition.
--DSC Menu--
MMSI Check
Input 9 digits
_________
<CLR˘Exit / ENT˘OK>--DSC Menu--Set upDEL:INDV ID ≤DEL:Group IDOffset Time˘MMSI Check ≥--DSC Menu--Select ItemPosition Input
Received Calls

[Juanitu]

{quote=maka}
This code programming can be performed only once.
After the code programming, it can be changed only
by your dealer or distributor.

Originalmente publicado por Kane

Si, pero...

Este tipo de información debería estar en la primera páina, en varios idiomas, con letra grande y negrita, y fondo amarillo.

Yo mismo introduje el MMSI de mi JRC-RT-2500 en su día, y ahora se que si me hubiese equivocado lo habría pasado un poquito mal.....

¿Cuántos usuarios habrán tenido el problema de programar un MMSI distinto o erróneo?

[Kane]

Muchos. Yo, entre ellos, y varias veces. Pero todos los arradios que son programables también son desprogramables y luego reprogramables. Sólo hay que saber como hacerlo.

Faltaría más...

Originalmente publicado por Juanitu

Este tipo de información debería estar en la primera páina, en varios idiomas, con letra grande y negrita, y fondo amarillo.

Yo mismo introduje el MMSI de mi JRC-RT-2500 en su día, y ahora se que si me hubiese equivocado lo habría pasado un poquito mal.....

¿Cuántos usuarios habrán tenido el problema de programar un MMSI distinto o erróneo?

[TAMAMOANA]

Me uno a la fiesta..... Soy tan "listo" que he comprado una radio de respeto/bricolajes/trasteos y es esta

Como no tengo mmsi ni falta que me hace, pienso que por lo menos, lo lógico es quitar el programado no sea que en algún momento piensen que se hunde el anterior dueño del trasto.

Así que a ver si con un poquito de suerte sale algo que no sea con un martillo y escoplo

[TAMAMOANA]

La palabra CONFIDENCIAL prometía, pero ........menudo chasco.

Por lo menos saco en claro, que no hay que conectar la emisora a un ordenador y aparentemente todo se hace desde la propia radio.

CONFIDENTIAL / Uniden Marine Dealers Only
TECHNICAL SERVICE INFORMATION Revised june 7 – 2005
Brand : UNIDEN Type: OCEANUS DSC/ATIS Es la misma que la rt2500
1. MMSI
1A. After purchase the user can program, one time only, the MMSI in the radio.
This is described in the user manual.
1B. To reprogram the MMSI ID the radio needs to be serviced at a Uniden Marine
Dealer that has a RESET JIG. (also to reprogram ATIS ID)
This item can be purchased from Avera B.V. The Netherlands.
1C. Procedure to reset the radio for new MMSI ID:
1. Make sure power radio is off.
2. Connect the reset jig to the accessory cable of the radio.
(red arrows on connectors!)
3. Push and hold CH UP on the radio while turning power on.
4. If display reads: “MMSI ID CLR”
reset has been succesful and MMSI ID can be reprogrammed
5. If display reads: MMSI ID INIT
* the radio has not been initialized yet
* the reset jig is not connected properly
* the reset jig is broken
In this case: Put power off, wait some minutes and follow complete procedure
again. (See step 4)
Note: During testing the RESET JIG it happened that all MMSI numbers from the
directory were deleted!
2. ATIS ID
2A. How to program ATIS is not mentioned in the user manual !
2B.1. Situation “Out of the box”:
Put power on
Press “menu”” Display “DSC Call”
Press “CH Down” Display “SET UP”
Press “Select” Display “Directory”
Press 6x “CH Down (*1) Display “ATIS ID”
Press “Select” Display “AT “ and “ID 000000000”
The first number after “ID” is not blinking, than it is NOT possible to program an ATIS
number.
2B.2 To program ATIS:
Turn power OFF
Press simultaneously “Menu” and “HI/LO” and put power on
Press “menu”” Display “DSC Call”
Press “CH Down” Display “SET UP”
Press “Select” Display “Directory”
Press 6x “CH Down (*1) Display “ATIS ID”
Press “Select” Display “AT “ and “ID 000000000”
The first number after “ID” is now blinking, and it is POSSIBLE to program an ATIS
number!
Use the numbers on the keypad of the microphone to program the ATIS number.
An ATIS number has 10 digits, the first digit is a “9” and is pre-programmed in the
unit, so you enter only the last 9 digits.
After entering the 9 digits press “ENTER”. Display “ATIS ID”
Turn power off.
Now the ATIS code is programmed in the transceiver.
2B.3 When ATIS is programmed
When a user repeats the procedure mentioned under 1 he will find the ATIS number
in the display, but NO blinking digit, so not possible to change anymore.
2B.4 To RE-Programme ATIS
Repeat as described under 2.
2C. Procedure to reset the radio for blank (000000000) new ATIS ID:
To do this the radio needs to be serviced at a Uniden Marine Dealer that has a
RESET JIG. This item can be purchased from Avera B.V. The Netherlands.
1. Make sure power radio is off.
2. Connect the reset jig to the accessory cable of the radio.
(red arrows on connectors!)
3. Push and hold CH DOWN on the radio while turning power on.
4. If display reads: “ATIS CLR”
reset has been succesful and ATIS can be reprogrammed
5. If display reads: ATIS ID INIT
 the radio has not been initialized yet
 the reset jig is not connected properly
 the reset jig is broken
In this case wait some minutes and follow complete procedure again.
See step 4.
2D. Procedure to edit new ATIS
Please read instructions under 2B.2
3. Seagoing Mode and Inland Waterway Mode
The radio can be switched from “Seagoing Mode” to “Inland Waterway Mode”.
3A. This is mentioned in the user manual.
Press PA/MODE to switch from mode.
3B. When “WX” blinks in the display the radio is in “Inland Waterway” Mode.
4. Enable 9 extra channels
4A. The radio comes with channels for “Seagoing Mode” and “Inland Waterway
Mode”. In some countries channels in the VHF marine band are used that are not in
the standard list of channels. If a user has a license for using these channels he
needs to visit a Uniden Marine Dealer to activate this function.
4B. There are 4 extra modes:
Mode 1 L1/L2/F1/F2/F3
Mode 2 L1/L2/L3/F1/F2/F3
Mode 3 30/31
Mode 4 M1 (display N1)
4C. Procedure to activate extra modes:
1. Make sure radio is off.
2. Press simultaneously SCAN and HI/LO while turning power on.
3. Repeat step 1 and 2 to move to next mode.
4. After mode 4 the radio starts up in original mode again.
Note: Radio always start up in the last selected mode.
5. UIC/ USA – International – Canada
5A. The radio can be switched from not only for Europe from ‘Inland Waterways’ to
‘Seagoing Mode’ but also from International to USA and Canada frequency chart.
5B. Procedure to activate UIC:
1. Make sure radio is off.
2. Press simultaneously Select and HI/LO while turning power on.
3. Repeat step 1 and 2 to move to next mode.
Note: Detailed information about the frequencies and channels for the different
modes can be found in the operation specifications
AVF129 V3

http://www.servicedocs.com/ARTIKELEN/11100237650001.pdf