La Taberna del Puerto Greatblue360
"Se navega por los astros, por la mar, por la tierra, por las gentes, por los sentimientos...Se navega." Altair
VHF: Canal 77   
Regresar   La Taberna del Puerto > Foro > Foros Náuticos > Foro Náutico Deportivo

Avisos

 
 
Herramientas Estilo
  #11  
Antiguo 09-02-2015, 13:02
Avatar de GermanR
GermanR GermanR esta desconectado
Hermano de la costa
 
Registrado: 27-10-2006
Localización: Cantábrico
Edad: 67
Mensajes: 2,522
Agradecimientos que ha otorgado: 1,026
Recibió 766 Agradecimientos en 375 Mensajes
Sexo:
Predeterminado Re: Proyecto OpenPlotter

Cita:
Originalmente publicado por sailoog.com Ver mensaje
ostras, no conocia ese video, está genial.

aquí está este tambien bastante detallado:
http://nmearouter.com/docs/ais/aerial.html
Este es el montaje ?

Collinear Coax AIS antenna - Recommended
AIS, antenna, RTL-SDR, Software Defined Radio, 820T, testing, review, DIY guideLength about 120 cm, costs 1 euros, works just as good as an 80 euro discone antenna. The antenna and the RTL stick fits into your pocket for AIS reception anywhere you can bring your laptop with you.
The best is that you only need to buy enough coax to reach from your laptop to your antenna site, plus 1 metre for the antenna, and you have a working AIS receiver.
The antenna is basically two 61 cm long coax cables, connected the wrong way for the antenna bit (center to braid and braid to center). You need to make four connections, two in the antenna proper and two at the bottom of the antenna to the coax cable you use to bring the signal to the RTL stick.
Twist the connections or use quick connectors; both work. For permanent installations you’re advised to use shrink-wrap (plastic tube that melts with a lighter) or lots of electrical tape.
As the antenna is flexible you need some form of support: the bottom half of a two-piece fishing rod or a PVC pipe sealed at one end is a permanent solution.

- Top section: measure 616 mm from end of coax,
- Mark with electrical tape, plus about 5 centimetres one end to have enough wire for connections.
- Bottom section: 616 mm for the antenna, plus enough both ends for connections.
- Cut the outer plastic cover lengthwise, carefully not to cut the center of the cable.
- Remove the plastic outer shell.
- Separate the braid from the center cable.
- Twist the braid.
- Cut off enough plastic cover from the center that you can wrap the braid around it. Cut it above the braid end so you can keep them separate.
- If you bend the center a little bit out from the cable that makes wrapping easier.


Veo que hay dos partes ¿activas? que se unen a un coaxial que va al receptor SDR. ¿este coaxial último puede tener cualquier longitud?.
¿sirve esta antena, con sus limitaciones, para una radio DEGEN?
¿Coaxial de 75 o de 50 Ohms?. He visto, en uno de esos enlaces, que hay quien recomienda 50?

Muchas gracias¡¡¡¡¡

__________________
Navigare necesse est .............
 

Greatblue360


Reglas del foro
No puedes crear discusiones
No puedes responder a mensajes
No puedes editar tus adjuntos
No puedes editar tus mensajes

BB code está activado
Emoticonos está activado
El código [IMG] está activado
El código HTML está desactivado
Ir a


Todas las horas son GMT +1. La hora es 11:11.


Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
© La Taberna del Puerto